FAQs

Sandpaper is made by bonding an abrasive grain like aluminum oxide, garnet or silicon carbide to a backing material. It is used to remove material from surfaces, either to make them smoother, to remove a layer of a substance like paint, or to make the surface rougher. The type and size of grain, the type of adhesive and the type of backing material all have an effect on the suitability of sandpaper for a particular job.

Abrasive paper works a lot like any other cutting tool, just on a smaller scale. The particles used to make sandpaper have a number of sharp edges that cut or shave away the material the same way a saw blade does.

Aluminum oxide, silicon carbide and garnet are the three major types of sandpaper on the market.

Aluminum oxide is a man-made material which is one of the most common woodworking abrasives. Aluminum oxide is a good all-surface general purpose sanding grain. Aluminum oxide cuts faster and lasts longer than garnet.

Garnet is a natural mineral that is an excellent abrasive for general wood sanding. Garnet produces a finer and softer scratch pattern and is often used for final sanding. Garnet also has the tendency to seal off a wood’s grain, which allows pigmented stains to penetrate certain woods more evenly.

Silicon carbide is suitable for both wet and dry sanding and is also known as ‘waterproof’ paper. Silicon carbide is good for sanding hard materials such as stone, porcelain and glass. Silicon carbide is fast-cutting and almost as hard as diamond. Silicon carbide is greatly used during automotive painting and repair. 

Grit is the number of abrasive grain particles per inch of sandpaper. The lower the grit, the bigger the grain and the coarser the sandpaper. Higher grit sandpaper has smaller grains. This means that it takes more grains to fill up a square inch, which helps give the sandpaper a smoother feel.

Be sure to take all appropriate safety precautions, especially when power sanding. You should always refer to the power tool manufacturer's instructions.

It is best to use progressively finer grits of sandpaper until you get the desired finish. This way each progressive grit of sandpaper removes the scratches from the previous grit. Skipping grits to save time will often have you sanding longer.

Be sure not to use excessive pressure when you sand, let the abrasive grit do the work. Using excessive pressure will only clog the paper or cause the paper to wear out much more quickly.

When sanding wood, sand along the grain, not across it. On a smooth, non-grained surface, move the sandpaper in small circular motions.

Open-coat means that there is space in between the particles that make up the sandpaper. This helps prevent clogging by giving the material that you are working on a place to go.

Closed-coat means there is little or no space in between the particles. Closed-coat is used more with sanding metal and some wood finishes and has a tendency to easily clog.

Sandpaper has many types of backing material. This includes paper, cloth and fiber. Paper backing is most commonly used material for hand sanding. Cloth backing is more durable than paper and is better at bending and flexing and is mostly used with power tool abrasives. Fiber backing, which is very hard and strong, is used for resin bonded fiber discs.

The weight of the backing is usually designated by a letter. For paper, the letters range from A to F, with A being the lightest and F the heaviest. Letter classification is different for cloth, with the weight of the backing being, from lightest to heaviest: J, X, Y, T and M.

The chart below is handy for approximate equivalents to metric.

9mm	3/8 inch
12mm	½ inch
18mm	¾ inch
24mm	1 inch
36mm	1-1/2 inch
42mm	1-3/4 inch
48mm	2 inches
60mm	2-1/2 inches
72mm	3 inches
96mm	4 inches
120mm	5 inches
144mm	6 inches
50M	55 Yards
55M	60 Yards
66M	72 Yards
100M	110 Yards
132M	145 Yards
411M	450 Yards
711M	750 Yards
914M	1,000 Yards
1,500M	1,640 Yards

What is Gold Flex? 
A term used by Ali Industries for sandpaper with white Aluminum Oxide grit. This top of the line Aluminum Oxide grit is sharper, and has a stearate coating allowing a cooler cut, and preventing the sandpaper from loading up.

What is Red Flex? 
A term used by Ali Industries for sandpaper with white Aluminum Oxide grit. This top of the line Aluminum Oxide grit is sharper, cuts quicker, and our product is manufactured on latex backed paper which adds strength to the paper as well as flexibility.

What is stearate? 
A soap-like substance to reduce clogging (“stearated” or “nonclog” sandpaper). Such paper is useful for sanding resinous woods and some finishes. Because it can leave a deposit, stearated paper should not be used if a water-based finish is planned.

Can I use Gator Finishing Products sandpaper with water?
Only sandpaper clearly identified as “Waterproof or wet/dry sanding’” should be used with water. The pre-cut sanding sheets appear to be too short. A very short overlap on the sander’s base is all the length needed. The clamp will assure a good hold.

How can I extend the life of my sanding belt? An abrasive belt cleaning stick cleans off dust particles and lubricates to minimize dust collection. The belt cleaning stick can also extend the life of sanding disc and drums.

Where can I purchase Gator Finishing Products?
Gator Finishing Products can be purchased through our partners.